Volgende week beurtje voor de Parlee (overgenomen van zeer gewaardeerd forumlid @csteenbe) en moet nodig balhoofdlagers vervangen. Headset is Canecreek Forty maat 40-IS41-42.
Vraag me nu even af welke lagers hier voor geschikt zijn. Op de site van Canecreek begrijp ik in ieder geval dat IS41 voor 41mm lagers staat.
Tips voor lagers en adressen welkom.
Balhoofdlagers Canecreek
Het is IS41 òf IS42, niet beide. Scheelt 0,85 mm.
Deze past onderaan ook: https://www.bike-components.de/en/Cane- ... up-p35107/
Specifiek losse lagers voor de Forty zie ik ook even niet.
Deze past onderaan ook: https://www.bike-components.de/en/Cane- ... up-p35107/
Specifiek losse lagers voor de Forty zie ik ook even niet.
Ik heb er onlangs hier gekocht voor een canecreek headset: https://www.bike-discount.de/en/buy/can ... n40-826556
op de site van canecreek kan zie ik onderstaand overzicht: let vooral op de hoeken van de lagers, dat is niet zo eenvoudig te meten
EC30 will take a 38mm bearing
EC34 will take a 41mm bearing
ZS44 will take a 41mm bearing
ZS49 will take a 41mm bearing
EC44/40 will take a 52mm bearing
EC44/33 will take a 47mm bearing
EC49 will take a 52mm bearing
ZS56 will take a 52mm bearing
ZS62 will take a 52mm bearing
IS41 will take a 41mm bearing
IS42 will take a 42mm bearing
IS52 will take a 52mm bearing
All complete Cane Creek headset assemblies (top or bottom) will use a 36x45 degree contact angle bearing, with the exception of our IS47/33 and EC44/33 headset assemblies. IS47/33 and EC44/33 will use a 45x45 degree contact angle bearing.
op de site van canecreek kan zie ik onderstaand overzicht: let vooral op de hoeken van de lagers, dat is niet zo eenvoudig te meten
EC30 will take a 38mm bearing
EC34 will take a 41mm bearing
ZS44 will take a 41mm bearing
ZS49 will take a 41mm bearing
EC44/40 will take a 52mm bearing
EC44/33 will take a 47mm bearing
EC49 will take a 52mm bearing
ZS56 will take a 52mm bearing
ZS62 will take a 52mm bearing
IS41 will take a 41mm bearing
IS42 will take a 42mm bearing
IS52 will take a 52mm bearing
All complete Cane Creek headset assemblies (top or bottom) will use a 36x45 degree contact angle bearing, with the exception of our IS47/33 and EC44/33 headset assemblies. IS47/33 and EC44/33 will use a 45x45 degree contact angle bearing.
Verzinkte lagers? Ik heb meervoudige ervaring met Cane Creek forty en zijn voorlopers. Maar Cane creek heeft RVS lagerringen, geen verzinkte....JDW schreef: ↑25 feb 2020 10:28 Ik heb er onlangs hier gekocht voor een canecreek headset: https://www.bike-discount.de/en/buy/can ... n40-826556
Laatst gewijzigd door klimmer op 25 feb 2020 18:06, 1 keer totaal gewijzigd.
https://www.canecreek.com/product/forty/
NEW! The new ZN40 bearings are a zinc-coated, machined steel cartridge bearing with hardened steel balls. The new material is much more corrosion-resistant, which vastly increases the longevity of the 40 series headsets.
NEW! The new ZN40 bearings are a zinc-coated, machined steel cartridge bearing with hardened steel balls. The new material is much more corrosion-resistant, which vastly increases the longevity of the 40 series headsets.